[June-2019-New]Full Version 640-875 Exam Dumps PDF and VCE 268Q for Free Download

2019 Latest Braindump2go CCNA Service Provider 640-875 SPNGN1 Dumps with PDF and VCE New Updated Today! Following are some new 640-875 Exam Questions:

1.|2019 Latest 640-875 Exam Dumps (PDF & VCE) Instant Download:

https://www.braindump2go.com/640-875.html

2.|2019 Latest 640-875 Exam Questions & Answers Instant Download:

https://drive.google.com/drive/folders/0B75b5xYLjSSNZzFaMmY3c3JkWlk?usp=sharing

New Question
Refer to the exhibit. Both ComputerA and Server1 have gigabit interface cards. Switch1 and Switch2 are both Cisco Catalyst 2960 Series Switches. The EtherChannel link between the switches is fully operational. The switches use src-dst-mac load-balancing mode.
What is the theoretical maximum bandwidth that is available for copying files from ComputerA to Server1 by using FTP?

A. 1 Gbps
B. 200 Mbps
C. 100 Mbps
D. 400 Mbps

Answer: C

New Question
Two sites each have a different ASN. Which method do you use to share routing information between the sites?

A. EIGRP
B. IGP
C. static routing
D. OSPFv3
E. BGP

Answer: E

New Question
You configure a network to use IPv6, and you use RIPng as the routing protocol. What is the maximum hop count to use to install a route in the routing table?

A. 15
B. 16
C. 255
D. 65535

Answer: A

New Question
Refer to the exhibit. Two routers are named R1 and R2. R1 runs Cisco IOS Software. R2 runs Cisco IOS XR Software. To form an EIGRP IPv6 adjacency between the two routers, which three configurations must you add? (Choose three.)

A. On R1, configure router-id with an IPv4 address.
B. On R1, configure router-id with an IPv6 address.
C. On R1, enter the no shutdown command inside the IPv6 EIGRP process.
D. On R1 and R2, enter the eigrp no shutdown command inside the interfaces.
“Pass Any Exam. Any Time.” – www.actualtests.com 119 Cisco 640-875 Exam
E. On R1, configure IPv6 unicast routing in config mode.
F. On R2, configure IPv6 unicast routing in config mode.

Answer: ACE

New Question
Which statement about VRFs is true?

A. One interface can be a member of multiple VRFs.
B. Each VRF has its own routing table, but it has a shared FIB.
C. Each VRF has its own routing table and its own FIB.
D. Each VRF has its own routing table, and it does not have an FIB.

Answer: C

New Question
You plan to configure NAT by using these guidelines:
– Implement NAT for the inside network 192.168.1.0/128 to the range of 209.165.201.1 to 209.165.201.5/128.
– Create a static association for the server 192.168.1.129 to the public IP address of 209.165.201.6.
– Implement PAT for the IP address range of 192.168.2.0/24 with the outside interface.
Which commands should you use to configure NAT?

A. access-list 1 permit 192.168.1.0 0.0.0.128
access-list 2 permit 192.168.2.0 0.0.0.255
ip nat pool NATCustomerA 209.165.201.1 209.165.201.5 netmask 0.0.0.128
ip nat inside source list 1 pool NATCustomerA
ip nat inside source static 192.168.1.129 209.165.201.6
ip nat inside source list 2 interface g1/0/0 overload interface f0/0
description CustomerFacing Interface
ip nat inside
interface g1/0/0
description
PublicWan
ip nat outside
B. access-list 1 permit 192.168.1.0 0.0.0.127
access-list 2 permit 192.168.2.0 0.0.0.255
ip nat pool NATCustomerA 209.165.201.1 209.165.201.5 netmask 255.255.255.128
ip nat inside source list 1 pool NATCustomerA
ip nat inside source static 192.168.1.129 209.165.201.6
ip nat inside source list 2 interface g1/0/0 overload interface f0/0
description CustomerFacing Interface
ip nat inside
interface g1/0/0
description PublicWan
ip nat outside
C. access-list 1 permit 192.168.1.0 0.0.0.128
access-list 2 permit 192.168.2.0 0.0.0.255
ip nat pool NATCustomerA 209.165.201.1 209.165.201.5 prefix 25
ip nat inside source list 1 pool NATCustomerA
ip nat inside source static 192.168.1.129 209.165.201.6
ip nat inside source list 2 interface g1/0/0
interface f0/0
description CustomerFacing Interface
ip nat inside
interface g1/0/0
description PublicWan
ip nat outside
D. access-list 1 permit 192.168.1.0 0.0.0.127
access-list 2 permit 192.168.2.0 0.0.0.255
ip nat pool NATCustomerA 209.165.201.1 209.165.201.5 prefix 25
ip nat inside source list 1 pool NATCustomerA overload
ip nat inside source static 192.168.1.129 209.165.201.6
ip nat inside source list 2 interface g1/0/0
interface f0/0
description CustomerFacing Interface
ip nat inside
interface g1/0/0
description PublicWan
ip nat outside

Answer: B

New Question
Refer to the exhibit. How many IP addresses does Router1 have that are available for DHCP clients?

A. 100
B. 99
C. 254
D. 199

Answer: B

New Question
Which type of ICMP message is generated when a datagram is discarded because the TTL reaches a value of 0?

A. Type 0 (Echo Reply)
B. Type 12 (Parameter Problem)
C. Type 11 (Time Exceeded)
D. Type 16 (Information Reply)
E. Type 10 (Source Quench)

Answer: C

New Question
In IPv6, which kind of record is used for reverse lookups?

A. nibble
B. AAAA
C. PTR
D. APL

Answer: C

New Question
Refer to the exhibit. A Cisco IOS Router has the configuration that is shown in the exhibit.
The Cisco IOS Router is replaced by a Cisco IOS XR device.
To duplicate the IPv6 EIGRP parameters of the Cisco IOS Router, which configuration should you use on the Cisco IOS XR device?

A. interface Loopback 0
ipv6 address 2001:db8:aaaa::1/128
!
interface gigabitEthernet 1/0/1
ipv6 enable
ipv6 address 2001:db8:bbbb::1/64
!
router eigrp 100
interface loopback 0
interface gigabitethernet 1/0/1
exit
commit
B. interface Loopback 0
ipv6 address 2001:db8:aaaa::1/128
!
interface gigabitEthernet 1/0/1
ipv6 enable
ipv6 address 2001:db8:bbbb::1/64
!
router eigrp 100
address-family ipv6
interface loopback 0
interface gigabitethernet 1/0/1
exit
commit
C. interface Loopback 0
ipv6 address 2001:db8:aaaa::1/128
ipv6 eigrp 100
!
interface gigabitEthernet 1/0/1
ipv6 address 2001:db8:bbbb::1/64
ipv6 router eigrp 100
!
ipv6 router eigrp 100
no shutdown
exit
commit
D. interface Loopback 0
ipv6 address 2001:db8:aaaa::1/128
commit
!
interface gigabitEthernet 1/0/1
ipv6 enable
ipv6 address 2001:db8:bbbb::1/64
commit
!
router eigrp 100
address-family ipv4
interface loopback 0
interface gigabitethernet 1/0/1
commit

Answer: B

New Question
DOCSIS architecture includes which two primary components? (Choose two.)

A. a DSL modem
B. a cable modem
C. CMTS
D. UMTS
E. an IP PBX

Answer: BC


!!!RECOMMEND!!!

1.|2019 Latest 640-875 Exam Dumps (PDF & VCE) Instant Download:

https://www.braindump2go.com/640-875.html

2.|2019 Latest 640-875 Study Guide Video Instant Download:

https://youtu.be/OAO4uJZZvys