2017 June New Updated PCNSE7 Exam Dumps with PDF and VCE Free Shared in www.Braindump2go.com Today!
100% Real Exam Questions! 100% Exam Pass Guaranteed!
1.|2017 New PCNSE7 PDF and PCNSE7 VCE 131Q&As Download:
2.|2017 New PCNSE7 Questions and Answers PDF Download:
A Palo Alto Networks firewall is being targeted by an NTP Amplification attack and is being flooded with tens thousands of bogus UDP connections per second to a single destination IP address and post.
Which option when enabled with the correction threshold would mitigate this attack without dropping legitirnate traffic to other hosts insides the network?
A. Zone Protection Policy with UDP Flood Protection
B. QoS Policy to throttle traffic below maximum limit
C. Security Policy rule to deny trafic to the IP address and port that is under attack
D. Classified DoS Protection Policy using destination IP only with a Protect action
Step 1: Configure a DoS Protection profile for flood protection.
1. Select Objects > Security Profiles > DoS Protection and Add a profile Name.
2. Select Classified as the Type.
3. For Flood Protection, select the check boxes for all of the following types of flood protection:
Other IP Flood
Step 2: Configure a DoS Protection policy rule that specifies the criteria for matching the incoming traffic.
This step include: (Optional) For Destination Address, select Any or enter the IP address of the device you want to protect.
Which Security Policy Rule configuration option disables antivirus and anti-spyware scanning of server-to-client flows only?
A. Disable Server Response Inspection
B. Apply an Application Override
C. Disable HIP Profile
D. Add server IP Security Policy exception
In the Other Settings section, select the option to Disable Server Response Inspection. This setting disables the antivirus and anti-spyware scanning on the server-side responses, and thus reduces the load on the firewall.
Which three options are available when creating a security profile? (Choose three)
B. File Blocking
C. Url Filtering
E. Threat Prevention
Using the URL Category as match criteria allows you to customize security profiles (antivirus, anti-spyware, vulnerability, file-blocking, Data Filtering, and DoS) on a per-URL-category basis.
Given the following table. Which configuration change on the firewall would cause it to use 10.66.24.88 as the next hop for the 192.168.93.0/30 network?
A. Configuring the administrative Distance for RIP to be lower than that of OSPF Int.
B. Configuring the metric for RIP to be higher than that of OSPF Int.
C. Configuring the administrative Distance for RIP to be higher than that of OSPF Ext.
D. Configuring the metric for RIP to be lower than that OSPF Ext.
The best route is then selected among them based on Administrative Distance (AD) value of routing protocols which routes came from and that route is marked with flag A, stating that it is the Active route.
Administrative distance (AD) is an arbitrary numerical value assigned to dynamic routes, static routes and directly-connected routes. The value is used by vendor-specific routers to rank routes from most preferred to least preferred. When multiple paths to the same destination are available, the router uses the route with the lowest administrative distance and inserts the preferred route into its routing table.
A company hosts a publically accessible web server behind a Palo Alto Networks next generation firewall with the following configuration information.
– Users outside the company are in the “Untrust-L3” zone
– The web server physically resides in the “Trust-L3” zone.
– Web server public IP address: 184.108.40.206
– Web server private IP address: 192.168.1.10
Which two items must be NAT policy contain to allow users in the untrust-L3 zone to access the web server? (Choose two)
A. Untrust-L3 for both Source and Destination zone
B. Destination IP of 192.168.1.10
C. Untrust-L3 for Source Zone and Trust-L3 for Destination Zone
D. Destination IP of 220.127.116.11
Which two interface types can be used when configuring GlobalProtect Portal?(Choose two)
A. Virtual Wire
C. Layer 3
GlobalProtect portal requires a Layer 3 or loopback interface for GlobalProtect clients to connect to.
What can missing SSL packets when performing a packet capture on dataplane interfaces?
A. The packets are hardware offloaded to the offloaded processor on the dataplane
B. The missing packets are offloaded to the management plane CPU
C. The packets are not captured because they are encrypted
D. There is a hardware problem with offloading FPGA on the management plane
A network Administrator needs to view the default action for a specific spyware signature. The administrator follows the tabs and menus through Objects> Security Profiles> Anti- Spyware and select default profile.
What should be done next?
A. Click the simple-critical rule and then click the Action drop-down list.
B. Click the Exceptions tab and then click show all signatures.
C. View the default actions displayed in the Action column.
D. Click the Rules tab and then look for rules with “default” in the Action column.
All Anti-spyware and Vulnerability Protection signatures have a default action defined by Palo Alto Networks. You can view the default action by navigating to Objects > Security Profiles > Anti-Spyware or Objects > Security Profiles >Vulnerability Protection and then selecting a profile. Click the Exceptions tab and then click Show all signatures and you will see a list of the signatures with the default action in the Action column. To change the default action, you must create a new profile and then create rules with a non-default action, and/or add individual signature exceptions to Exceptions in the profile.
How does Panorama handle incoming logs when it reaches the maximum storage capacity?
A. Panorama discards incoming logs when storage capacity full.
B. Panorama stops accepting logs until licenses for additional storage space are applied
C. Panorama stops accepting logs until a reboot to clean storage space.
D. Panorama automatically deletes older logs to create space for new ones.
When Panorama reaches the maximum capacity, it automatically deletes older logs to create space for new ones.
Which three function are found on the dataplane of a PA-5050? (Choose three)
A. Protocol Decoder
B. Dynamic routing
D. Network Processing
E. Signature Match
In these devices, dataplane zero, or dp0 for short, functions as the master dataplane and determines which dataplane will be used as the session owner that is responsible for processing and inspection.
The data plane provides all data processing and security detection and enforcement, including:
* (B) All networking connectivity, packet forwarding, switching, routing, and network address translation
* Application identification, using the content of the applications, not just port or protocol
* SSL forward proxy, including decryption and re-encryption
* Policy lookups to determine what security policy to enforce and what actions to take, including scanning for threats, logging, and packet marking
* Application decoding, threat scanning for all types of threats and threat prevention
* Logging, with all logs sent to the control plane for processing and storage
E: The following diagram depicts both the hardware and software architecture of the next-generation firewall
C: Management is done in the control plane.
1.|2017 New PCNSE7 PDF and PCNSE7 VCE 131Q&As Download:
2.|2017 New PCNSE7 Study Guide Video: